Regulation of the temperature of an individual heat point by changing the speed of the asynchronous motor
https://doi.org/10.30724/1998-9903-2021-23-4-156-165
Abstract
THE PURPOSE. To develop and investigate a mathematical model of an operating object – an individual heat point with two methods of controlling the temperature of the coolant. In the first case, the control of the temperature of the coolant is considered, with the help of a control valve installed on a real object. In the second case, a more reliable and less energy-consuming solution is proposed – replacing the control valve with a frequency- controlled electric drive operating according to the proposed optimal algorithm.
METHODS. When solving this problem, the method of computer simulation modeling, implemented by means of Matlab Simulink, was used.
RESULTS. The article deals with the problems that arise during the operation of an individual heating point. Possible solutions to the problem associated with the failure of the control valve are given. A solution for regulating the temperature of the coolant is proposed, based on the use of a frequency-controlled electric drive of the electric pump. To implement the proposed solution, no redevelopment of the premises is required, only the installation of a frequency converter on the pump already available in the device of an individual heat station is necessary.
CONCLUSION. The conducted research has a practical focus, since the proposed solution is implemented at the existing facility. The use of a frequency-controlled electric drive of a centrifugal pump made it possible to increase the reliability of the existing facility. The results obtained during the simulation allow us to draw a conclusion about the feasibility of using the proposed solution.
About the Authors
T. V. Sinyukova
Lipetsk State Technical University
Russian Federation
Russian Federation
Tatyana V. Sinyukova
Lipetsk
A. V. Sinyukov
Lipetsk State Technical University
Russian Federation
Russian Federation
Alexey V. Sinyukov
Lipetsk
References
1. Rotov PV, Sivukhin AA, Rotova MA, et al. Ob effektivnosti upravleniya tsirkulyatsiei goryachei vody. Izvestiya vysshikh uchebnykh zavedenii. Problemy energetiki. 2020;6:117-129.
2. Meshcheryakov V, Sinyukova T, Sinyukov A, et al. Analysis of the effectiveness of using the block for limiting the vibrations of the load on the mechanism of movement of the bogie with various control systems. E3S Web of Conferences. Sustainable Energy Systems: Innovative Perspectives (SES-2020), Saint-Petersburg, Russia, 2020, 220, 01059, October 29- 30.
3. Meshcheryakov V, Sinykova T, Sinyukov A, et al. Modeling and analysis of vector control systems for asynchronous motor. High Speed Turbomachines and Electrical Dreves Conference 2020 (HSTED-2020), Prague, Czech Republic.
4. Sinyukova TV, Levin P.N. Metod uskoreniya puskovogo algoritma dlya pryamogo upravleniya momentum. Pribory i sistemy. Upravlenie, kontrol', diagnostika. 2012;12:60-67.
5. Grachieva EI, Shakurova ZM, Abdullazyanov RE. Comparative analysis of the most common deterministic methods for determining energy losses in workshop networks. Problems of Energy. 2019;5:87-96.
6. Grachieva EI, Gorlov AN, Shakurova ZM. Analysis and estimation of power saving in systems of in-plant power supply. Energy problem. 2020;2:65-74.
7. Grachieva EI, Naumov OV. Loss of electricity and the effectiveness of the operation of equipment workshop networks. Monograph. M.: RUSAINS, 2017. 168.
8. Khasanov SR, Gracheva EI, Toshkhodzhaeva MI, et al. Reliability modeling of high- voltage power lines in a sharply continental climate. E3S Web of Conferences. 2020;178:01051.
9. Grachieva EI, Naumov OV. Evaluation criteria of contact group technical state concerning electrical appliances. International Journal of Pharmacy and Technology. 2016;8(4):26763–26770.
10. Dovgun V, Temerbaev S, Chernyshov M, et al. Distributed power quality conditioning system for three-phase four-wire low voltage networks. Energies. 202;13(18):4915. doi: 10.3390/en13184915.
11. Tarnekar SG, Bante KG, Tutakane DR. Use Of Smart Drives and PLC for Energy Saving. 2018 International Conference on Smart Electric Drives and Power System (ICSEDPS). Nagpur. 2018. P. 2.
12. Shilin AA, Bukreev VG. Nelineinaya matematicheskaya model' teplopotrebleniya s uchetom kharakteristik elementov teplovogo uzla. Nauchnyi vestnik NGTU. 2012;2(47):107- 114.
13. Mecke R. Efficient induction motor drive with multilevel inverter and variable rotor flux. 2017 IEEE 26ht International Symposium on Industrial Electronics (ISIE). Edinburdh, UK. 2017. P. 1.
14. Yilong Wang; Hassan H. Eldeeb; Haisen Zhao; Osama A. Mohammed. Sectional Variable Frequency and Voltage Regulation Control Strategy for Energy Saving in Beam Pumping Motor Systems. IEEE Access (Volume: 7). China. 2019;7:4.
15. Yusufov ShA, Magomedov TYu. Individual'nye teplovye punkty: ikh preimushchestva pered tsentral'nymi v oblasti zhilishchno-kommunal'nogo khozyaistva. Molodoi uchenyi. 2018;36 (222):11-14.
16. Soldatenkov AS, Potapenko AN, Glagolev SN. Razrabotka i issledovanie matematicheskoi modeli upravleniya avtomatizirovannym individual'nym punktom. Nauchno- tekhnicheskie vedomosti Sankt-Peterburgskogo gosudarstvennogo politekhnicheskogo universiteta. Informatika. Telekommunikatsii. Upravlenie. 2012;1(140):41-48.
17. Kungs YaA, Tsuglenok NV, Zhivotov ON, et al. Individual'nyi teplovoi punkt (konueptual'nyi proekt). Vestnik KrasGAU. 2014;11:196-199.
18. Petrov SP, Podmaster'ev KV, Pilipenko AV, et al. Metody kontrolya i upravleniya teplovymi i gidravlicheskimi rezhimami individual'nykh teplovykh punktov zdanii. Fundamental'nye i prikladnye problemy tekhniki i tekhnologii. 2020;3 (341):171-179.
19. Sabirova LR. Postroenie avtomatizirovannogo individual'nogo punkta na osnove iskusstvennogo intellekta. Nauchnomu progressu – tvorchestvo molodykh. 2019;2:164-166.
20. Levtsev AP, Lapin ES. Issledovanie energoeffektivnogo membrannogo nasosa v sisteme individual'nogo teplovogo punkta zdaniya. Privolzhskii nauchnyi zhurnal. 2018;4(48):53-59.
Review
For citations:
Sinyukova T.V., Sinyukov A.V. Regulation of the temperature of an individual heat point by changing the speed of the asynchronous motor. Power engineering: research, equipment, technology. 2021;23(4):156-165. (In Russ.) https://doi.org/10.30724/1998-9903-2021-23-4-156-165
Views:
437
Email this article 